Gordon Brush Logo
323-724-7777 / 800-950-7950
Log In   Cart (0)   Contact Us
Brush-A-Pedia® Brushes By Fill Material
Brushes By Handle Material
Brushes By Application
Brushes By NSN Number
Clearance Brushes
Brushes By Industry
Aerospace
Automotive
Electronics
Facility Management
Food Service
Forensics and Criminology
Janitorial
Material Handling and Packaging
Medical
Military
Pharmaceutical
Printing and Engraving
Stock Brushes
Abrasives & Buffs
Acid/Sash/Parts Cleaning Brushes
Applicator Brushes
Artist Brushes
Artist and Forensic Brushes
Block Brushes
Bore Brushes
Brushes By NSN Number
Duster Brushes
ESD and Cleanroom Brushes
Flow Thru Brushes
Handheld Brushes
Janitorial Brushes
Metal Free Tube Brushes
Metal Handle Brushes
Miniature Brushes
Non-Sparking Brushes
Paint Brushes and Accessories
Plastic Handle Brushes
Scratch and Plater Brushes
Specialty Brushes
Speedy Sweep®
Spiral/Twisted-in-Wire
Strip Brushes & Holders
Toothbrush Style
Upright Brushes
Utility Brushes
Wheel, Rotary, Cylinder Brushes
Wood Handle Brushes
Brushes By Application
Artist Brushes
Disinfecting & Sterilizing Brushes
ESD and Cleanroom Brushes
FDA Compliant Brushes
Forensic Brushes
Janitorial Brushes
Medical Brushes
Non-Sparking Brushes
Paint Brushes and Accessories
ISO 9001:2015 Certified Accessibility
Proud To Be An AMERICAN Manufacturer
ISO 9001:2015 Certified
          Proud To Be An AMERICAN Manufacturer
323-724-7777 / 800-950-7950
Gordon Brush Logo
323-724-7777 / 800-950-7950
Log In   Cart (0)
Gordon Brush Logo
All
Log In   Cart (0)

Contact Us
Gordon Brush Logo


 

Grounding Brushes

Grounding Brushes are so named because they are intended to be permanently mounted and serve as a flexible, inexpensive conduit to ground.

Discharging Conductive Surfaces

When grounding a isolated or insulated conductor, contact need only be made in one location on the isolated surface. In a conductor charges travel freely so a single point of contact is sufficient to discharge the entire ungrounded surface.

An example of this type of grounding was the problem experienced by a roller coaster operator whose cars ran on steel rails but had nylon wheels. The highly charged cars would arc as they approached the metal railing of the station. Installing a brush like those pictured below that touched the bottom of the car before it reached the station served to discharge the car and avert a serious potential problem.

These brushes are normally made using a conductive fiber, for example, conductive nylon, brass, steel or stainless steel.

The brushes used to ground conductive surfaces can be as inexpensive as those pictured left or as sophisticated as the brush shown on the right. This grounding brush is made of 316 stainless steel and has a brush face with a 1” forward reach that is pushed forward continuously at a preset thrust into the grounding steel plate to insure thousands of hours of continuous use without adjustment or need of inspection.

Discharging Non-Conductive Surfaces

Discharging a non-conductive surface is considerably more difficult because the charges can not move, they can not equalize and, only the specific area of the charged surface that is touched is discharged. For example, if you brushed the top side of a plastic sheet with a conductive brush, the top side only would be discharged. The sides and bottom would still have the original charge.

When used for grounding, strip brushes are normally thin [as there is no electrical advantage to thick] and are normally filled with very fine diameter conductive or static dissipative material. If the intent is to touch to charged surface with the brush, the fiber is continuous as shown on the top right.

If inductive discharge is used, the fill material is normally spaced 1mm or 2mm apart. The corona discharge is enhanced by the fineness of the point of the conductor. Those shown on the right have a point that measures approximately 5 angstroms. Thunderon® tape has a conductive peel-and-stick backing and can be applied to any conductive surface.

Thunderon® is a patented organic fiber of copper sulfide chemically bonded to acrylic and nylon fibers, Thunderon® performs better than conventional carbon, stainless steel, or metal-plated fibers. Thunderon® offers unmatched corona discharge, superior conductivity, enhanced abrasion resistance and superior bend recovery, and antibacterial and odor-elimination properties. It is available in a wide range of materials, including filament, cloth, rope, tape, yarn and brushes.

Thunderon® is ideal for use in printing, office machines, business machines, photo finishing, paper converting, plastic converting, and textile machinery. It also has bacteriostatic applications in hospitals and clean room environments.

 

 

Join Our Mailing List

We respect your privacy and will not share your information with third parties

COPYRIGHT © 2024 GORDON BRUSH MFG. CO., INC.
ALL RIGHTS RESERVED

WEBSITE DEVELOPED BY:  EMSAR DESIGN LTD
Gordon Brush Logo
COPYRIGHT © 2024 GORDON BRUSH MFG. CO., INC.   |   ALL RIGHTS RESERVED   |   WEBSITE DEVELOPED BY: EMSAR DESIGN LTD